Select language

Choose the language for the tools.

Electrical Fundamentals & Circuit Analysis

RMS, Peak & Peak-to-Peak Voltage Calculator

Convert any one RMS, peak, peak-to-peak, or rectified-average voltage into the other three values for a sine, square, or triangle wave.

RMS, peak, and average equations

The waveform determines the crest factor Kp and the rectified-average factor Ka.

Vpeak = Kp × Vrms
Vrms = Vpeak / Kp
Vpp = 2 × Vpeak
Vavg = Ka × Vpeak

where:

Vrms
Root-mean-square voltage[V]
Vpeak
Peak voltage from zero[V]
Vpp
Peak-to-peak voltage[V]
Vavg
Full-wave rectified average[V]
Kp
Peak-to-RMS crest factor
Ka
Rectified-average-to-peak factor

For a sine wave Kp = √2 and Ka = 2/π; the square and triangle factors differ.

How RMS, peak, and average differ

RMS represents the equivalent heating magnitude of an AC waveform. Peak is the maximum magnitude from zero, peak-to-peak spans the full waveform, and rectified average is the mean of the absolute voltage.

Worked sine-wave example

For a 120 V RMS sine wave, peak voltage is 120 × √2 = 169.7 V, peak-to-peak voltage is 339.4 V, and the full-wave rectified average is 108.0 V.

Vpeak = 169.7 V

Vpp = 339.4 V

Vavg = 108.0 V

Method & Sources

Method

Formula used

  • Vpeak = Kp × Vrms
  • Vrms = Vpeak / Kp
  • Vpp = 2 × Vpeak
  • Vavg = Ka × Vpeak

Input basis

The waveform determines the crest factor Kp and the rectified-average factor Ka.

  • Waveform
  • Known voltage
  • Entered voltage [V]
  • Vrms — Root-mean-square voltage [V]
  • Vpeak — Peak voltage from zero [V]
  • Vpp — Peak-to-peak voltage [V]
  • Vavg — Full-wave rectified average [V]
  • Kp — Peak-to-RMS crest factor
  • Ka — Rectified-average-to-peak factor

Units

V

Display and rounding

No separate display or rounding rule is stated on this page.

Scope and limits

  • The waveform is symmetric and has zero mean before full-wave rectification.
  • Average means the average absolute value after full-wave rectification.
  • The selected waveform determines the crest and average factors.
  • Do not apply these factors to pulse waveforms, rectifier ripple, or waveforms with a DC offset.
  • RMS voltage is not the same as average voltage, peak voltage, or peak-to-peak voltage.
  • For a sine wave Kp = √2 and Ka = 2/π; the square and triangle factors differ.

Sources

  • Estimation basis: published page formula, assumptions, and warningsEstimation basisNo separate public standard is cited; the published equation and stated input scope form a planning or screening basis.

Waveform conversion factors

Each waveform has a different relationship between RMS, peak, and rectified average.

WaveformPeak / RMSAverage / peak
Sine wave√22/π
Square wave11
Triangle wave√31/2

Why symmetric waveforms are required

These factors assume a zero-mean symmetric waveform. A DC offset shifts the average and changes RMS, while pulses and rectifier ripple require a waveform definition or direct measurement.

Using the result in AC calculations

Use RMS voltage for AC power, current, and power-factor equations. Peak and peak-to-peak values are useful for insulation, component voltage, waveform, and measurement checks.

Assumptions

  • The waveform is symmetric and has zero mean before full-wave rectification.
  • Average means the average absolute value after full-wave rectification.
  • The selected waveform determines the crest and average factors.

Important Warnings

  • Do not apply these factors to pulse waveforms, rectifier ripple, or waveforms with a DC offset.
  • RMS voltage is not the same as average voltage, peak voltage, or peak-to-peak voltage.

FAQ

What is 120 V RMS for a sine wave?

For a sine wave, 120 V RMS gives about 169.7 V peak, 339.4 V peak-to-peak, and 108.0 V rectified average.

Does a square wave use the same factors as a sine wave?

No. For a symmetric bipolar square wave, RMS magnitude equals peak magnitude and rectified average also equals peak magnitude.

What is the rectified average of a sine wave?

The full-wave rectified average of a sine wave is 2/π times its peak, or about 0.6366 times peak.

Can these values determine AC power?

RMS voltage is used in AC power equations, but power also requires RMS current and the applicable power factor.

Can the calculator handle a DC offset?

No. A DC offset changes RMS and average values, so it must be calculated from the complete waveform definition.