MPPT controller sizing equations
Current, cold-voltage, and array-power checks are applied independently.
Voc,string = Nseries × Voc,moduleIcontroller ≥ 1.25 × Isc,moduleVcontroller ≥ 1.25 × Voc,stringPcontroller,max ≥ Nseries × Pmodulewhere:
- Nseries
- Modules connected in series
- Isc,module
- Module short-circuit current[A]
- Voc,module
- Module open-circuit voltage[V]
- Pmodule
- Module rated power[W]
For four 450 W modules, the minimum current class is 15 A, voltage class is 250 V, and PV power rating must be at least 1,800 W.
How to size an MPPT controller
A controller must pass current, voltage, and power checks. Series modules add Voc but keep module Isc, so the 125% current basis remains 14.375 A in the example.
- Enter series module quantity and module ratings.
- Multiply Isc by 1.25 for controller current.
- Multiply string Voc by 1.25 for the cold-voltage requirement.
- Confirm the controller maximum PV power is at least array W.
Worked four-module example
Four 450 W modules in series produce an 1,800 W string, 198.4 V Voc, and 11.5 A Isc.
125% × 11.5 A = 14.375 A → 15 A
125% × 198.4 V = 248 V → 250 V
| Check | Result |
|---|---|
| String Voc | 198.4 V |
| String Isc | 11.5 A |
| String power | 1,800 W |
| Controller current class | 15 A |
| 125% Voc requirement | 248 V |
| Selected voltage class | 250 V |
| Maximum PV power rating | ≥ 1,800 W |
Method & Sources
Method
Formula used
Voc,string = Nseries × Voc,moduleIcontroller ≥ 1.25 × Isc,moduleVcontroller ≥ 1.25 × Voc,stringPcontroller,max ≥ Nseries × Pmodule
Input basis
Current, cold-voltage, and array-power checks are applied independently.
- Modules in series
- Module power [W]
- Module Voc [V]
- Module Isc [A]
- Nseries — Modules connected in series
- Isc,module — Module short-circuit current [A]
- Voc,module — Module open-circuit voltage [V]
- Pmodule — Module rated power [W]
Units
W · V · A
Display and rounding
No separate display or rounding rule is stated on this page.
Scope and limits
- All modules in the string have the same model and operating conditions.
- The 125% Voc factor is used as the low-temperature voltage allowance required by this page.
- Controller ratings are rounded to disclosed current and voltage classes; the product MPPT window and maximum PV power must still be verified.
- The datasheet maximum PV power can depend on battery voltage. Confirm it at the actual system voltage.
- Verify absolute maximum PV voltage at the coldest site temperature, conductor current, fuse coordination, and controller temperature derating.
- For four 450 W modules, the minimum current class is 15 A, voltage class is 250 V, and PV power rating must be at least 1,800 W.
Sources
- NFPA 70, National Electrical Code (NEC), 690.8Edition not stated on this page; clause and table identifiers are preserved verbatim.
String and combiner checks
A complete design also checks module temperature coefficients, maximum system voltage, string fuse, combiner current, and controller MPPT window.
Why the rounded class is not the final product
Controller voltage classes are for screening. The actual product must support the exact cold Voc, MPPT range, maximum PV power at battery voltage, and continuous output current.
Assumptions
- All modules in the string have the same model and operating conditions.
- The 125% Voc factor is used as the low-temperature voltage allowance required by this page.
- Controller ratings are rounded to disclosed current and voltage classes; the product MPPT window and maximum PV power must still be verified.
Important Warnings
- The datasheet maximum PV power can depend on battery voltage. Confirm it at the actual system voltage.
- Verify absolute maximum PV voltage at the coldest site temperature, conductor current, fuse coordination, and controller temperature derating.