Select language

Choose the language for the tools.

Solar, Battery & Backup Power

Solar Voltage Drop Calculator

Calculate DC solar voltage drop from string Isc, one-way cable length, Vmp, and copper conductor size using a 125% design current and 2% target.

NEC 690.8

PV DC voltage-drop equations

The design current applies 1.25 times Isc and the resistance includes both circuit conductors.

Idesign = 1.25 × Isc
Vdrop = 2 × ρ × L × Idesign / A
Drop(%) = 100 × Vdrop / Vmp
PASS when Drop(%) ≤ 2%

where:

Isc
String short-circuit current[A]
ρ
Copper resistivity[Ω·mm²/m]
L
One-way cable length[m]
A
Conductor area[mm²]
Vmp
String voltage at maximum power[V]

At 13 A Isc, 30 m, 200 V, and copper conductor, 4 mm² gives 2.1% and 6 mm² gives 1.4%.

How to calculate PV DC voltage drop

The design current is 125% of string Isc. The two-wire voltage drop uses the outgoing-and-return length through copper resistance, then divides by string Vmp for the percentage.

  1. Enter string Isc and Vmp.
  2. Enter the physical one-way cable length.
  3. Select the copper conductor size.
  4. Compare the result with the 2% DC target.

Worked 4 mm² and 6 mm² comparison

At 16.25 A design current, 30 m one-way, and 200 V Vmp, 4 mm² copper produces 4.27 V and fails; 6 mm² produces 2.84 V and passes.

Copper sizeVoltage dropPercentageResult
4 mm²4.27 V2.1%FAIL
6 mm²2.84 V1.4%PASS

Method & Sources

Method

Formula used

  • Idesign = 1.25 × Isc
  • Vdrop = 2 × ρ × L × Idesign / A
  • Drop(%) = 100 × Vdrop / Vmp
  • PASS when Drop(%) ≤ 2%

Input basis

The design current applies 1.25 times Isc and the resistance includes both circuit conductors.

  • String Isc [A]
  • One-way cable length [m]
  • String Vmp [V]
  • Copper conductor size
  • Isc — String short-circuit current [A]
  • ρ — Copper resistivity [Ω·mm²/m]
  • L — One-way cable length [m]
  • A — Conductor area [mm²]
  • Vmp — String voltage at maximum power [V]

Units

A · m · V · Ω·mm²/m · mm²

Display and rounding

No separate display or rounding rule is stated on this page.

Scope and limits

  • The circuit is a two-wire copper DC run and one-way length is entered.
  • Copper resistivity is 0.0175 Ω·mm²/m at 20 °C, shared with the site DC voltage-drop basis.
  • The 2% limit is a design target on this page; confirm inverter and project requirements.
  • Use hot-conductor resistance and include terminals, fuses, connectors, and junction losses for final cable design.
  • Voltage drop does not establish cable current-carrying capacity, short-circuit withstand, or DC isolator rating.
  • At 13 A Isc, 30 m, 200 V, and copper conductor, 4 mm² gives 2.1% and 6 mm² gives 1.4%.

Sources

  • NFPA 70, National Electrical Code (NEC), 690.8Edition not stated on this page; clause and table identifiers are preserved verbatim.

Cable and system checks

Voltage drop is separate from cable ampacity, short-circuit temperature rise, maximum DC voltage, isolation, and pull tension.

Temperature and connection losses

The displayed values use 20 °C copper resistivity. Hot conductors have higher resistance, and connectors, fuses, and isolators add additional voltage loss.

Assumptions

  • The circuit is a two-wire copper DC run and one-way length is entered.
  • Copper resistivity is 0.0175 Ω·mm²/m at 20 °C, shared with the site DC voltage-drop basis.
  • The 2% limit is a design target on this page; confirm inverter and project requirements.

Important Warnings

  • Use hot-conductor resistance and include terminals, fuses, connectors, and junction losses for final cable design.
  • Voltage drop does not establish cable current-carrying capacity, short-circuit withstand, or DC isolator rating.

FAQ

Why does 4 mm² fail the example?

The 125% design current is 16.25 A. A 30 m two-wire copper run at 4 mm² drops about 4.27 V, or 2.1% of 200 V, which exceeds the 2% target.

Why does 6 mm² pass?

Increasing conductor area reduces resistance. At 6 mm² the same run drops about 2.84 V, or 1.4%, which is below 2%.

Is one-way length doubled by the user?

No. Enter the physical one-way run. The DC two-wire formula already includes the outgoing-and-return resistance.

Why use 125% of Isc?

The page applies the stated NEC 690.8 design-current basis so voltage drop is checked above the module nameplate short-circuit current.

Can aluminum cable be used?

This page is intentionally limited to copper. Aluminum has different resistivity and termination requirements and is not silently substituted.