Select language

Choose the language for the tools.

Power Systems & Distribution

Neutral Current Calculator

Estimate fundamental and third-harmonic neutral current from three phase currents, then check total neutral utilization against an optional ampacity.

Neutral-current equations

The fundamental result uses the stated equal-angle phasor assumption. Third-harmonic phase components are summed in the neutral before combining by root-sum-square.

Fundamental neutral
IF = √(IA² + IB² + IC² − IA×IB − IB×IC − IC×IA)
Third-harmonic sum
I3N = 0.01 × (hA×IA + hB×IB + hC×IC)
Total neutral
IN = √(IF² + I3N²)
Ampacity utilization
Utilization = 100 × IN / Irated

where:

IA, IB, IC
Phase fundamental RMS currents[A]
IF
Fundamental neutral-current phasor magnitude[A]
hA, hB, hC
Third-harmonic content of each phase[%]
I3N
Arithmetic third-harmonic neutral sum[A]
IN
Total estimated neutral current[A]
Irated
Optional corrected neutral ampacity[A]

For 100/80/60 A with 30% third harmonic on each phase, the fundamental is 34.6 A, the harmonic sum is 72 A, and the total is 79.9 A.

How the neutral-current estimate works

Enter the three fundamental phase currents and, when relevant, each phase's third-harmonic percentage. The fundamental result uses the phasor relationship for equal displacement power-factor angles; the third-harmonic components are added arithmetically.

  1. Enter one simultaneous current for each phase.
  2. Enter each third-harmonic percentage, or leave all values at zero.
  3. Optionally enter corrected neutral ampacity.
  4. Review fundamental, harmonic, total current and utilization.

Three worked neutral-current cases

The examples separate the fundamental phasor result from the triplen harmonic component. The final value is the root-sum-square of those two components.

CaseFundamentalThird harmonicTotal
100 / 80 / 60 A34.6 A0 A34.6 A
100 / 80 / 60 A; 30% each34.6 A30 + 24 + 18 = 72 A79.9 A
100 / 100 / 100 A; 30% each0 A30 + 30 + 30 = 90 A90.0 A

Method & Sources

Method

Formula used

  • IF = √(IA² + IB² + IC² − IA×IB − IB×IC − IC×IA)
  • I3N = 0.01 × (hA×IA + hB×IB + hC×IC)
  • IN = √(IF² + I3N²)
  • Utilization = 100 × IN / Irated

Input basis

The fundamental result uses the stated equal-angle phasor assumption. Third-harmonic phase components are summed in the neutral before combining by root-sum-square.

  • Phase A fundamental current [A]
  • Phase B fundamental current [A]
  • Phase C fundamental current [A]
  • Phase A third-harmonic content [%]
  • Phase B third-harmonic content [%]
  • Phase C third-harmonic content [%]
  • Neutral conductor ampacity [A]
  • IA, IB, IC — Phase fundamental RMS currents [A]
  • IF — Fundamental neutral-current phasor magnitude [A]
  • hA, hB, hC — Third-harmonic content of each phase [%]
  • I3N — Arithmetic third-harmonic neutral sum [A]
  • IN — Total estimated neutral current [A]
  • Irated — Optional corrected neutral ampacity [A]

Units

A · %

Display and rounding

No separate display or rounding rule is stated on this page.

Scope and limits

  • The three phase currents represent one measurement window and have the same displacement power-factor angle.
  • Entered third-harmonic percentages are relative to each phase fundamental current and are treated as in-phase triplen components in the neutral.
  • The total combines the fundamental phasor result and the arithmetic third-harmonic sum by root-sum-square.
  • Different phase angles, other triplen orders, waveform phase data, or measured spectra can require a full harmonic phasor study.
  • NEC 220.61 is mentioned only as qualitative context; this calculator does not reproduce its detailed load-sizing provisions or establish code compliance.
  • For 100/80/60 A with 30% third harmonic on each phase, the fundamental is 34.6 A, the harmonic sum is 72 A, and the total is 79.9 A.

Sources

  • Estimation basis: published page formula, assumptions, and warningsEstimation basisNo separate public standard is cited; the published equation and stated input scope form a planning or screening basis.

Balanced fundamental does not mean zero neutral

Equal fundamental phase currents at 120-degree spacing cancel in the neutral. Third harmonics are separated by three times 120 degrees, or 360 degrees, so they occupy the same phase and add in the neutral.

100 A balanced fundamental → 0 A fundamental neutral

30% third harmonic on each phase → 30 + 30 + 30 = 90 A

Total neutral = 90.0 A

Ampacity and NEC context

The optional ampacity compares total neutral current with the corrected conductor capacity. NEC 220.61 is mentioned only as qualitative context for neutral-load sizing; this page does not restate detailed code provisions or claim compliance.

Assumptions

  • The three phase currents represent one measurement window and have the same displacement power-factor angle.
  • Entered third-harmonic percentages are relative to each phase fundamental current and are treated as in-phase triplen components in the neutral.
  • The total combines the fundamental phasor result and the arithmetic third-harmonic sum by root-sum-square.

Important Warnings

  • Different phase angles, other triplen orders, waveform phase data, or measured spectra can require a full harmonic phasor study.
  • NEC 220.61 is mentioned only as qualitative context; this calculator does not reproduce its detailed load-sizing provisions or establish code compliance.

FAQ

Why is fundamental neutral current nonzero for 100, 80, and 60 A?

The phase currents are not equal, so their 120-degree phasors do not cancel completely. The phasor equation gives about 34.6 A before harmonics.

Why do third harmonics add instead of cancel?

Three third-harmonic components separated by three times 120 degrees share the same phase. They therefore add arithmetically in the neutral, even when the fundamental currents are balanced.

What does the optional neutral ampacity do?

It calculates total neutral utilization and flags 80% or higher for caution and above 100% as over capacity. It does not automatically select the conductor or protection.

Can I use this with unequal phase angles?

No. This page assumes equal displacement power-factor angles. Unequal angles require the actual phase-angle measurements and a full phasor calculation.

Does NEC 220.61 determine the answer automatically?

No. The article is only qualitative context here. Use the adopted code, load characteristics, harmonic spectrum, and engineered neutral sizing for the actual project.