Select language

Choose the language for the tools.

Cable Management & Installation

Conduit Bending Calculator

Calculate field marks for offsets, three-point saddles, four-point saddles and 90-degree stubs using documented bender charts.

Conduit Bending Calculator

Field multipliers approximate practical marks; they are not exact sharp-corner trigonometric results.

L = H × M
S = H × k
X = Hstub − d

where:

L
Distance between offset marks[in]
H
Offset depth[in]
M
Field angle multiplier
S
Field shrink allowance[in]
k
Shrink factor per inch of height
X
Stub arrow-mark position[in]
Hstub
Finished stub height[in]
d
Bender take-up[in]

Calculation basis

Calculate field marks for offsets, three-point saddles, four-point saddles and 90-degree stubs using documented bender charts.

Field multipliers approximate practical marks; they are not exact sharp-corner trigonometric results.

Verified tables and sources

Offset values are from Gardner Bender B1000. Stub take-up and three-point saddle values are from Klein. These are tool instructions, not NEC dimensional tables.

AngleMultiplierShrink per inch
10°60.0625
22.5°2.60.1875
30°20.25
45°1.40.375
60°1.20.5

Klein stub take-up table

No. The listed values are from the Klein guide. Check the actual tool and make a trial bend.

ParameterValue
1/2 EMT5 in
3/4 EMT6 in
1 EMT8 in
1/2 Rigid6 in
3/4 Rigid8 in

Worked examples

The field multiplier is 2.0: 6 × 2 = 12 in between marks.

The chart uses 1/4 in per inch of depth, so 6 × 1/4 = 1.5 in.

For a 12 in stub using the 1/2 in EMT Klein bender, the arrow mark is 12 − 5 = 7 in from the end.

Method & Sources

Method

Formula used

  • L = H × M
  • S = H × k
  • X = Hstub − d

Input basis

Field multipliers approximate practical marks; they are not exact sharp-corner trigonometric results.

  • Bend type
  • Offset or obstacle height [in]
  • Offset bend angle
  • Center saddle angle
  • Distance to obstacle center [in]
  • Flat clearance including bend allowance [in]
  • Finished stub height [in]
  • Klein bender conduit size
  • L — Distance between offset marks [in]
  • H — Offset depth [in]
  • M — Field angle multiplier
  • S — Field shrink allowance [in]
  • k — Shrink factor per inch of height
  • X — Stub arrow-mark position [in]
  • Hstub — Finished stub height [in]
  • d — Bender take-up [in]

Units

in

Display and rounding

No separate display or rounding rule is stated on this page.

Scope and limits

  • Field multipliers approximate practical marks; they are not exact sharp-corner trigonometric results.
  • Take-up depends on the bender, conduit and shoe. Four-point saddle flat length must include clearance for the obstacle and bend radii.

Sources

Application limits

Take-up depends on the bender, conduit and shoe. Four-point saddle flat length must include clearance for the obstacle and bend radii.

Assumptions

  • Field multipliers approximate practical marks; they are not exact sharp-corner trigonometric results.

Important Warnings

  • Take-up depends on the bender, conduit and shoe. Four-point saddle flat length must include clearance for the obstacle and bend radii.

FAQ

What is the spacing for a 6 in offset at 30 degrees?

The field multiplier is 2.0: 6 × 2 = 12 in between marks.

How much shrink does that offset require?

The chart uses 1/4 in per inch of depth, so 6 × 1/4 = 1.5 in.

How is a three-point saddle marked?

For the Klein 45-degree center saddle, advance the center by 3/16 of the height and place outer marks 2.5 times the height either side. The 60-degree option uses 1/4 and 2.0.

Is four-point saddle shrink doubled?

Yes, this model uses two equal mirrored offsets. The entered flat length separates the inner marks.

Can I use these take-up values with any bender?

No. The listed values are from the Klein guide. Check the actual tool and make a trial bend.